Popular Searches: furniture, engineer, computer, engineers, tour, Cranes, refractory bad material, water treatment, gears, ceramics, job work, rings piston, fedora, tester, dot creation
Corporate Online, India Yellow Pages, Business to Business Portal, Indian B2B Portal
Welcome to Corporateonline.in! Join Free | Sign In Registered Users : 1904
  (Enter Part of your City)
SWETA ASSOCIATION OF FABRICATION 'N' ERECTION » All Products

SWETA ASSOCIATION OF FABRICATION 'N' ERECTION
Co-current Configuration
In a co-current flow spray dryer, the spray is directed into the hot air entering the dryer and both pass through the chamber in the same direction. Co-current dryers are the preferred design for heat sensitive products because the hottest drying air...more
[More Info] [Send Inquiry for Co-current Configuration]
Counter Current Two Stage Flash Drying System
This is another special configuration of flash dryers in which the initial feed material to be dried in a flash dryer is semi-dried using the spent drying air from the second stage. This semi-dried product is then introduced into the second stage of ...more
[More Info] [Send Inquiry for Counter Current Two Stage Flash Drying System]
Counter-current Configuration
In this configuration, the spray and the air are introduced at opposite ends of the dryer, with the atomizer positioned at the top and the air entering at the bottom. A counter-current dryer offers more rapid evaporation and higher energy efficiency ...more
[More Info] [Send Inquiry for Counter-current Configuration]
Counter-current Principle
Rotary dryers are commonly used in the minerals industry to dry a range of commodities including clay, gypsum, kaolin, limestone, mineral sand, potash and silica sand (Photo 54). They consist of a relatively long cylindrical shell, which ranges from ...more
[More Info] [Send Inquiry for Counter-current Principle]
Counter-current Principle1
Counter Current dryers are more suitable for materials that must be dried to very low levels of moisture, where the last traces of moisture are difficult to remove, or where an elevated product temperature is desirable. They are also used effectively...more
[More Info] [Send Inquiry for Counter-current Principle1]
Extended Residence Time Flash Dryer
In this configuration of flash dryers, the upper part of the flash tube has more cross-sectional area in order to reduce the flow velocity. Wider area typically includes an internal baffle arrangement. This concept enables extended residence time at ...more
[More Info] [Send Inquiry for Extended Residence Time Flash Dryer]
Flash Fluid Bed Drying System
Agitated flash dryers are used to avoid multiple passes of the product through the dryer. In this configuration, the feed material is transferred from an agitated feed tank through a screw feed into a flash-drying chamber provided with a rotor. T...more
[More Info] [Send Inquiry for Flash Fluid Bed Drying System]
Hot Air Generator-Direct & Indirect
Hot Air Generator-Direct & Indirect Direct gas fired. Indirect oil and gas fired....more
[More Info] [Send Inquiry for Hot Air Generator-Direct & Indirect]
Mixed Flow Configuration
This type of dryers combines both concurrent and counter current flow. In a mixed flow dryer, the air enters at the top and the atomizer is located at the bottom. Like the counter-current design, a mixed flow dryer exposes the driest particles to the...more
[More Info] [Send Inquiry for Mixed Flow Configuration]
Open Cycle Dryer
In an open cycle dryer, the drying air is drawn from the atmosphere, heated, conveyed through the chamber and then exhausted to the atmosphere. This is most commonly used design....more
[More Info] [Send Inquiry for Open Cycle Dryer]
Open System
Usually a push-pull system is used to balance the pressure to slightly negative in the free board of the fluid bed. Depending upon the product and available heat source, direct or indirect heating may be applied. Then the exhaust air is cleaned by ba...more
[More Info] [Send Inquiry for Open System]
P-type Ring Dryer
P-type ring dryer is used for heat sensitive materials. In this configuration, the semi-dried particles discharged from the manifold are exposed to the outlet temperature level. This configuration also provides for the extended residence time require...more
[More Info] [Send Inquiry for P-type Ring Dryer]
Partial Recycle Concept
Agitated flash dryers are used to avoid multiple passes of the product through the dryer. In this configuration, the feed material is transferred from an agitated feed tank through a screw feed into a flash-drying chamber provided with a rotor. The r...more
[More Info] [Send Inquiry for Partial Recycle Concept]
Rewet Agglomeration
In this configuration, a fine powder is conveyed to an agglomeration chamber where the powder is dispersed in air and contacted with a spray of liquid. Moist, porous agglomerates are formed and subsequently dried under lenient fluidization conditions...more
[More Info] [Send Inquiry for Rewet Agglomeration]
Ring Dryer
Ring Dryer...more
[More Info] [Send Inquiry for Ring Dryer]
Rotary Dryers
Rotary dryers are commonly used in the minerals industry to dry a range of commodities including clay, gypsum, kaolin, limestone, mineral sand, potash and silica sand (Photo 54). They consist of a relatively long cylindrical shell, which ranges from ...more
[More Info] [Send Inquiry for Rotary Dryers]
Semi-closed Cycle Dryer
This design is a hybrid configuration of both open and closed cycle dryers and it is not gas tight. There are many variations on this design, with the most important being the "direct heated" or "self-inertizing" system. In the self-inertizing design...more
[More Info] [Send Inquiry for Semi-closed Cycle Dryer]
Two Stage Dryer with Fluid Bed Dryer
In a two stage dryer, the moisture content of product leaving the chamber is higher (typically 5% - 10%) than for the final product. After leaving the chamber, the moisture content is further reduced during a second stage. Second stage drying may be ...more
[More Info] [Send Inquiry for Two Stage Dryer with Fluid Bed Dryer]
Two Stage Dryer with Vibrating Bed Dryer
In a two stage dryer, the moisture content of product leaving the chamber is higher (typically 5% - 10%) than for the final product. After leaving the chamber, the moisture content is further reduced during a second stage. Second stage drying may be ...more
[More Info] [Send Inquiry for Two Stage Dryer with Vibrating Bed Dryer]
Home | Advertise with us | Useful Links | Success Stories | Feedback | Careers | Contact us | Site Map | Terms of Use | Privacy & Policy | Join Free | FAQ

Products and services: A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z

Copyright © 2010-21 CORPORATE ONLINE. All rights reserved.